Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of VESTAMID® DX9330 - PA612 - Evonik Operations GmbH

Material Data Center offers the following functions for VESTAMID® DX9330:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Vestamid datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Informação do produto
Medium viscosity polyamide 612 resin

VESTAMID® DX9330 NC is a PA 612 base polymer without any stabilizers and other additives.

VESTAMID® DX9330 NC is suitable for both extrusion as well as injection molding. Usually VESTAMID® DX9330 NC is only used in special cases when additives are not preferable, or processing aids are not necessary, e.g. filament extrusion.

Based on the perfect balance of amino and carboxyl end groups this material is easy to process and to dye. The typical characteristics of PA 612 are moderate water absorption, good dimensional stability and almost unchanged properties at varying ambient humidity.
  
VESTAMID® DX9330 NC is supplied as cylindrical granules, ready for processing, in moisture-proof bags. The processing temperature should be within a range of 250°C to 290°C.

Pigmentation may affect values.

Inside the original and undamaged packaging, the product has a shelf life of at least 2 years when stored in dry rooms at temperatures not exceeding 30°C.

The results shown have been generated from a low number of production lots. Therefore, they are preliminary and not yet the result of a statistical evaluation. Therefore they must not be used to establish specifications. 

For information about processing of VESTAMID®, please follow the general commendations about “Processing of VESTAMID® compounds”. 

FOR FURTHER INFORMATION PLEASE CONTACT US AT EVONIK-HP@EVONIK.COM OR VISIT OUR PRODUCT AT  WWW.VESTAMID.COM
Características de processamento/físicasSeco / CondUnidadeMétodo de ensaio
ISO Dados
Índice de fluidez volumétrico, MVR 69 / * cm³/10min ISO 1133
Temperatura 240 / * °C -
Carga 10 / * kg -
Contração após a moldagem, paralelo 1.4 / * % ISO 294-4, 2577
Contração após a moldagem, perpendicular 1.4 / * % ISO 294-4, 2577
Propriedades mecânicasSeco / CondUnidadeMétodo de ensaio
ISO Dados
Módulo de tração 2196 / - MPa ISO 527
Tensão no escoamento 58 / - MPa ISO 527
Deformação no escoamento 4 / - % ISO 527
Deformação nominal na ruptura >50 / - % ISO 527
Resistência ao impacto Charpy , +23°C N / - kJ/m² ISO 179/1eU
Resistência ao impacto Charpy, -30°C N / - kJ/m² ISO 179/1eU
Res. impacto Charpy c/entalhe, +23°C 4.5 / - kJ/m² ISO 179/1eA
Type of failure C / - - -
Res. impacto Charpy c/entalhe, -30°C 4.5 / - kJ/m² ISO 179/1eA
Type of failure C / - - -
Propriedades térmicasSeco / CondUnidadeMétodo de ensaio
ISO Dados
Temperatura de fusão, 10°C/min 215 / * °C ISO 11357-1/-3
Temp. de transição vítrea, 10°C/min 44 / * °C ISO 11357-1/-2
Temperatura de deflexão térmica, 1.80 MPa 58 / * °C ISO 75-1/-2
Temperatura de deflexão térmica, 0.45 MPa 149 / * °C ISO 75-1/-2
Temperatura de amolecimento Vicat, B 180 / * °C ISO 306
Outras propriedadesSeco / CondUnidadeMétodo de ensaio
Absorção de água 2.8 / * % Sim. to ISO 62
Absorção de umidade 1.4 / * % Sim. to ISO 62
Densidade 1060 / - kg/m³ ISO 1183
Características
Processamento
Moldagem por injeção, Outros tipos de extrusão
Forma de entrega
Granulos, Cor natural
Aplicaciones
Filament for 3D Printing
Disponibilidade regional
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.