Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of VESTAMID® DX9303 BK E70288 - PA612-I - Evonik Operations GmbH

Material Data Center offers the following functions for VESTAMID® DX9303 BK E70288:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Vestamid datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Características de processamento/físicas - Propriedades mecânicas - Propriedades térmicas - Propriedades elétricas - Outras propriedades
Any use of this information falls under the rules of our disclaimer.
Informação do produto
High-viscosity, plasticized, heat- and light-stabilized, impact-modified polyamide 612 compound for extrusion

VESTAMID® DX9303 BK E70288 is a PA 612 extrusion compound developed for the production of tubing systems with higher requirements for heat resistance.

The melting point of VESTAMID® DX9303 BK E70288 is about 35°C higher than PA 11 and PA 12 compounds, allows higher peak temperatures in use. Thereby this compound fulfills the increased demands resulting from higher temperatures in the engine compartment.

If it is intended to use VESTAMID® DX9303 BK E70288 for fuel lines, certain preconditions must be observed. The Technical Marketing assists you in finding the suitable VESTAMID® compound.
At temperatures above 100°C tubing of VESTAMID® DX9303 BK E70288 allow a higher pressure load than tubing made of PA 12 compounds with comparable flexibility.

The process temperatures should be in the range of 240-270°C.

The material absorbs only little moisture. Therefore dimensions and properties of parts are nearly unaffected through ambient conditions.


Pigmentation may affect values.

Inside the original and undamaged packaging, the product has a shelf life of at least 2 years when stored in dry rooms at temperatures not exceeding 30°C.

For information about processing of VESTAMID®, please follow the general commendations about “Processing of VESTAMID® compounds”. 

FOR FURTHER INFORMATION PLEASE CONTACT US AT EVONIK-HP@EVONIK.COM
OR VISIT OUR PRODUCT AT  WWW.VESTAMID.COM

Características de processamento/físicasSeco / CondUnidadeMétodo de ensaio
ISO Dados
Índice de fluidez volumétrico, MVR 11 / * cm³/10min ISO 1133
Temperatura 275 / * °C -
Carga 5 / * kg -
Contração após a moldagem, paralelo 2.7 / * % ISO 294-4, 2577
Contração após a moldagem, perpendicular 0.9 / * % ISO 294-4, 2577
Propriedades mecânicasSeco / CondUnidadeMétodo de ensaio
ISO Dados
Módulo de tração 900 / 680 MPa ISO 527
Tensão no escoamento 38 / - MPa ISO 527
Deformação no escoamento 30 / - % ISO 527
Deformação nominal na ruptura >50 / - % ISO 527
Resistência ao impacto Charpy , +23°C N / N kJ/m² ISO 179/1eU
Resistência ao impacto Charpy, -30°C N / N kJ/m² ISO 179/1eU
Res. impacto Charpy c/entalhe, +23°C 87 / 135 kJ/m² ISO 179/1eA
Res. impacto Charpy c/entalhe, -30°C 11 / 15 kJ/m² ISO 179/1eA
Type of failure C / C(P)[C(P)] - -
Dureza Shore D 70 / * - ISO 7619-1
C(P): CAMPUS
Propriedades térmicasSeco / CondUnidadeMétodo de ensaio
ISO Dados
Temperatura de fusão, 10°C/min 211 / * °C ISO 11357-1/-3
Temp. de transição vítrea, 10°C/min 20 / * °C ISO 11357-1/-2
Temperatura de deflexão térmica, 1.80 MPa 60 / * °C ISO 75-1/-2
Temperatura de deflexão térmica, 0.45 MPa 142 / * °C ISO 75-1/-2
Temperatura de amolecimento Vicat, B 159 / * °C ISO 306
Coef. de expansão térmica linear, paralelo 150 / * E-6/K ISO 11359-1/-2
Coef. de expansão térmica linear, perpend. 120 / * E-6/K ISO 11359-1/-2
Flamabilidade a 1.5mm esp. nom. HB / * class IEC 60695-11-10
Espessuras do tubo de teste 1.6 / * mm -
Propriedades elétricasSeco / CondUnidadeMétodo de ensaio
ISO Dados
Constante dielétrica, 100Hz 4.7 / - - IEC 62631-2-1
Constante dielétrica, 1MHz 2.7 / - - IEC 62631-2-1
Fator de dissipação dielétrica, 100Hz 1450 / - E-4 IEC 62631-2-1
Fator de dissipação dielétrica, 1MHz 400 / - E-4 IEC 62631-2-1
Resistividade volumétrica específica 2E10 / 5.3E8 Ohm*m IEC 62631-3-1
Resistência elétrica 39 / 34 kV/mm IEC 60243-1
Índice comparativo de linha de fuga 600 / - - IEC 60112
Outras propriedadesSeco / CondUnidadeMétodo de ensaio
Absorção de água 2.4 / * % Sim. to ISO 62
Absorção de umidade 1 / * % Sim. to ISO 62
Densidade 1050 / - kg/m³ ISO 1183
Características
Processamento
Extrusão de tubos, Outros tipos de extrusão
Forma de entrega
Granulos, Negro
Aditivos
Plastificante
Características especiais
Alto impacto., Estável a luz, Estável contra o calor
Disponibilidade regional
América do Norte, Europa, Ásia Pacífico, America Centra e do Sul, Oriente/África
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.