Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultrafuse PLA PRO1 - PLA - BASF

Material Data Center offers the following functions for Ultrafuse PLA PRO1:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Ultrafuse datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Características de processamento/físicasValorUnidadeMétodo de ensaio
ISO Dados
Índice de fluidez volumétrico, MVR 18.2 cm³/10min ISO 1133
Temperatura 210 °C -
Carga 2.16 kg -
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de fusão, 10°C/min 175 °C ISO 11357-1/-3
Temp. de transição vítrea, 10 °C/min 63 °C ISO 11357-1/-2
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 1250 kg/m³ ISO 1183
3D DataValorUnidadeMétodo de ensaio
Other Standards[S]
Módulo de tração, flat 3170 MPa ISO 527
Módulo de tração, upright 2930 MPa ISO 527
Resistência à tração, flat 48 MPa ISO 527
Resistência à tração, upright 21.8 MPa ISO 527
Deformação na ruptura, flat 21.9 % ISO 527
Deformação na ruptura, upright 0.9 % ISO 527
Módulo de flexão, flat 2820 MPa ISO 178
Módulo de flexão, on-edge 2340 MPa ISO 178
Resistência à flexão, flat 92.4 MPa ISO 178
Resistência à flexão, on-edge 99.1 MPa ISO 178
Resistência ao impacto Charpy, +23°C, flat 20.4 kJ/m² ISO 179/1eU
Resistência ao impacto Charpy, +23°C, on-edge 18.8 kJ/m² ISO 179/1eU
S: These properties are reported by the producer according standards that are different to our defaults.
Características
Processamento
Additive Manufacturing
Forma de entrega
Monofilament
Certifications
Contém recursos renováveis
Disponibilidade regional
América do Norte, Europa, America Centra e do Sul
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.