Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of MAGNUM™ 1250 BG - ABS - Trinseo

Material Data Center offers the following functions for MAGNUM™ 1250 BG:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Magnum datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Características de processamento/físicasValorUnidadeMétodo de ensaio
ISO Dados
Índice de fluidez, MFI 1.7 g/10min ISO 1133
Temperatura 220 °C -
Carga 10 kg -
ASTM Dados
Índice de fluidez, MFI 1.7 g/10min ASTM D 1238
Temperatura 230 °C -
Carga 3.8 kg -
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Tensão no escoamento 33.7 MPa ISO 527
Módulo de flexão, 23°C 1810 MPa ISO 178
Impacto Izod com entalhe, +23°C 26 kJ/m² ISO 180/1A
Impacto Izod com entalhe 17 kJ/m² ISO 180/1A
Temperatura -30 °C -
ASTM Dados
Resistência à tração no escoamento 33.6 MPa ASTM D 638
Deformação na ruptura 60 % ASTM D 638
Módulo de flexão 2013 MPa ASTM D 790
Impacto Izod com entalhe, 1/8 in 358 J/m ASTM D 256
Impacto Izod com entalhe, baixa temperatura 187 J/m ASTM D 256
Temperatura -28.9 °C -
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de deflexão térmica, 1.80 MPa 85 °C ISO 75-1/-2
Temperatura de deflexão térmica , 0.45 MPa 101 °C ISO 75-1/-2
ASTM Dados
DTUL @ 66 psi 103 °C ASTM D 648
DTUL @ 264 psi 86.7 °C ASTM D 648
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 1050 kg/m³ ASTM D 792
Características
Processamento
Moldagem por sopro
Características especiais
Alto impacto., Estável contra o calor
Disponibilidade regional
América do Norte
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.