Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of ALCOM MS PP 4920 16080 - PP-T20 - MOCOM Compounds GmbH & Co. KG
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces
Check here, which other Alcom datasheets, application examples or technical articles are available in Material Data Center
Base Polymer | Polypropylene Homopolymer |
Filler/Additive System | 20 % talcum |
Special Features | scratch resistant,heat stabilised,easy release (demoulding) |
Market Segment | Automotive |
Typical Applications | injection moulded parts |
Características de processamento/físicas | Valor | Unidade | Método de ensaio | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO Dados | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Índice de fluidez volumétrico, MVR | 3 | cm³/10min | ISO 1133 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Temperatura | 230 | °C | - | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Carga | 2.16 | kg | - |
Propriedades mecânicas | Valor | Unidade | Método de ensaio | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO Dados | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Módulo de tração | 2400 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Tensão no escoamento | 29 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Deformação no escoamento | 7.4 | % | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistência ao impacto Charpy , +23°C | 60 | kJ/m² | ISO 179/1eU | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Res. impacto Charpy c/entalhe, +23°C | 6.5 | kJ/m² | ISO 179/1eA |
Propriedades térmicas | Valor | Unidade | Método de ensaio | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO Dados | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Temperatura de deflexão térmica, 1.80 MPa | 70 | °C | ISO 75-1/-2 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Temperatura de amolecimento Vicat, B | 95 | °C | ISO 306 |
Outras propriedades | Valor | Unidade | Método de ensaio |
Densidade | 1050 | kg/m³ | ISO 1183 |
Pre-Drying Conditions | in a dry air (dessiccant) dryer 60-90 °C for 2-4 h in an air circulating dryer 60-90 °C for 2-4 h dependant on moisture content |
Processing Injection Moulding | melt temperature 200-270 °C mould temperature 20-70 °C |
Storage | dry, protected from light |
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.