Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ALCOM ASA/PC 540/5 UV GY81-714MCF - (ASA+PC) - MOCOM Compounds GmbH & Co. KG

Material Data Center offers the following functions for ALCOM ASA/PC 540/5 UV GY81-714MCF:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Alcom datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Características de processamento/físicas - Propriedades mecânicas - Propriedades térmicas - Outras propriedades
Any use of this information falls under the rules of our disclaimer.
Informação do produto
Base PolymerPolycarbonate +Acrylonitrile Styrene Acrylate Blend
Filler/Additive SystemUV stabilised
Colourmetallic
Special Featureslow tendency to flow lines
Market Segmentelectrical and electronic,building and construction,sport and leisure
Typical Applicationshousings
Características de processamento/físicasValorUnidadeMétodo de ensaio
ISO Dados
Índice de fluidez volumétrico, MVR 18 cm³/10min ISO 1133
Temperatura 260 °C -
Carga 5 kg -
Propriedades mecânicasValorUnidadeMétodo de ensaio
ISO Dados
Módulo de tração 2450 MPa ISO 527
Resistência ao impacto Charpy , +23°C 90 kJ/m² ISO 179/1eU
Res. impacto Charpy c/entalhe, +23°C 20 kJ/m² ISO 179/1eA
Propriedades térmicasValorUnidadeMétodo de ensaio
ISO Dados
Temperatura de deflexão térmica, 1.80 MPa 105 °C ISO 75-1/-2
Temperatura de amolecimento Vicat, B 119 °C ISO 306
Flamabilidade a 1.5mm esp. nom. HB class IEC 60695-11-10
Espessuras do tubo de teste 1.5 mm -
Outras propriedadesValorUnidadeMétodo de ensaio
Densidade 1190 kg/m³ ISO 1183
Características
Processamento
Moldagem por injeção
Características especiais
Estabilidade a raios U.V./Intempéries
Características
Metallic effect
Aplicaciones
Construção, Elétrica e Eletrônica, Encapsulamento, Equipo deportivo
Disponibilidade regional
América do Norte, Europa, Ásia Pacífico, Oriente/África
Outras informações
Moldagem por injeção
Pre-Drying Conditionsin a dry air (dessiccant) dryer 90-110 °C
for 2-4 h
in an air circulating dryer 90-110 °C
for 4-8 h
dependant on moisture content
Processing Injection Mouldingmelt temperature 260-300 °C
mould temperature 60-90 °C
Storagedry, protected from light
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.