Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Xyron™ X304H - PPE-X40 - Asahi Kasei

Material Data Center offers the following functions for Xyron™ X304H:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Xyron datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
기계적 특성단위시험규격
ISO 데이터
인장 강도 61 MPa ISO 527
굴곡 계수, 23°C 7850 MPa ISO 178
굴곡 강도 111 MPa ISO 178
챠피 노치드 충격 강도, +23°C 3 kJ/m² ISO 179/1eA
열적 특성단위시험규격
ISO 데이터
하중하에서의 변형온도, 1.80 MPa 108 °C ISO 75-1/-2
선형 열팽창 계수, 평행 30 E-6/K ISO 11359-1/-2
1.5mm 평균두께에서의 난연성 HB class IEC 60695-11-10
테스트 두께 1.6 mm -
ASTM 데이터
DTUL @ 264 psi 110 °C ASTM D 648
전기적 특성단위시험규격
ISO 데이터
상대 유전율, 100Hz 3.4 - IEC 62631-2-1
상대 유전뮬, 1MHz 3.3 - IEC 62631-2-1
소산 인자, 100Hz 70 E-4 IEC 62631-2-1
소산 인자, 1MHz 90 E-4 IEC 62631-2-1
부피 저항 1E14 Ohm*m IEC 62631-3-1
표면 저항 1E16 Ohm IEC 62631-3-2
기타 특성단위시험규격
밀도 1400 kg/m³ ISO 1183
Processing Recommendation Injection Molding단위시험규격
Pre-drying - Temperature 90 - 100 °C -
Pre-drying - Time 2 - 4 h -
용융수지온도 250 - 300 °C -
성형온도 60 - 90 °C -
특징
생산 공정
사출 성형
특성
Low Warpage
지역별 검색
쨘횕쩐횈쨍횧쨍짰횆짬, 짱쨌쨈, 쩐횈쩍횄쩐횈 횇횂횈챵쩐챌 횁철쩔짧
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.