Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of TENAC™-C Z3513 - POM - Asahi Kasei

Material Data Center offers the following functions for TENAC™-C Z3513:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Tenac datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 機械的特性 - 熱的特性 - 電気的特性. - その他の特性. - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristics乾燥/調湿単位テスト基準
ISO データ
メルトボリュームレイト, MVR 2.6 / * cm³/10min ISO 1133
温度 190 / * °C -
荷重 2.16 / * kg -
メルトフローレート, MFI 3 g/10min ISO 1133
機械的特性乾燥/調湿単位テスト基準
ISO データ
引張弾性率 2500 / - MPa ISO 527
降伏応力 62 / - MPa ISO 527
破壊ひずみ 40 / - % ISO 527
曲げ弾性率, 23°C 2400 / - MPa ISO 178
ノッチ付きシャルピー衝撃強さ, +23°C 8 / - kJ/m² ISO 179/1eA
ASTM数据
引張強度 62 / - MPa ASTM D 638
破断伸び 35 / - % ASTM D 638
曲げ弾性率 2450 / - MPa ASTM D 790
曲げ強さ 88 / - MPa ASTM D 790
ロックウェル硬度 M 78 / - ASTM D 785
Taber耐摩耗性 14 mg/1000 cycles ASTM D 1044
ノッチ付きIzod衝撃強さ, 1/8 in 96 / - J/m ASTM D 256
熱的特性乾燥/調湿単位テスト基準
ISO データ
荷重たわみ温度, 1.80 MPa 93 / * °C ISO 75-1/-2
荷重たわみ温度, 0.45 MPa 153 / * °C ISO 75-1/-2
線膨張係数, 平行 100 / * E-6/K ISO 11359-1/-2
ASTM数据
線膨張係数, 平行 100 E-6/K ASTM D 696
DTUL @ 66 psi 158 °C ASTM D 648
DTUL @ 264 psi 110 °C ASTM D 648
電気的特性.乾燥/調湿単位テスト基準
ASTM数据
耐電圧, 短い時間 19 / - kV/mm ASTM D 149
表面抵抗率 * / 1E17 Ohm ASTM D 257
体積抵抗率 1E16 / - Ohm*cm ASTM D 257
耐アーク 250 / - s ASTM D 495
その他の特性.乾燥/調湿単位テスト基準
密度 1410 / - kg/m³ ISO 1183
吸水率, 24hr 0.2 % ASTM D 570
密度 1410 kg/m³ ASTM D 792
Processing Recommendation Injection Molding値単位テスト基準
Pre-drying - Temperature 80.9 °C -
Pre-drying - Time 3 - 4 h -
樹脂温度 180 - 210 °C -
金型温度 60 °C -
特殊な特性
成形加工法.
射出成形.
納入形状.
ペレット.
特殊な特性.
紫外線安定化.
な特性
Copolymer
領域別の利用可能性
北アメリカ., ヨーロッパ., アジア/太平洋地域., 南・中央アメリカ., 近東/アフリカ
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.