Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of RADITECK P RV400K 1700 NT - PPS-GF40 - RadiciGroup High Performance Polymers

Check here, which other Raditeck datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - 機械的特性 - 熱的特性 - 電気的特性. - その他の特性. - 機能

Any use of this information falls under the rules of our disclaimer.

商品の説明文

PPS 40% glass fibre reinforced injection moulding grade. Heat stabilized. Natural colour.

Balanced matching of excellent chemical resistance, inherent flame retardancy and very good heat ageing properties retention. Suitable for parts requiring very high stiffness and high mechanical strength.

Processing/Physical Characteristics	値	単位	テスト基準
ISO データ
成形収縮率, 平行	0.1	%	ISO 294-4, 2577
成形収縮率, 直角	0.6	%	ISO 294-4, 2577

機械的特性	値	単位	テスト基準
ISO データ
引張弾性率	14600	MPa	ISO 527
破壊応力	195	MPa	ISO 527
破壊ひずみ	1.8	%	ISO 527
シャルピー衝撃強さ, +23°C	50	kJ/m²	ISO 179/1eU
ノッチ付きシャルピー衝撃強さ, +23°C	10	kJ/m²	ISO 179/1eA

熱的特性	値	単位	テスト基準
ISO データ
溶融温度, 10°C/min	280	°C	ISO 11357-1/-3
荷重たわみ温度, 1.80 MPa	265	°C	ISO 75-1/-2
荷重たわみ温度, 0.45 MPa	270	°C	ISO 75-1/-2
線膨張係数, 平行	16	E-6/K	ISO 11359-1/-2
線膨張係数, 直角	46	E-6/K	ISO 11359-1/-2
Yellow Card 可用	はい	-	-
厚さhでの燃焼性	V-0	class	IEC 60695-11-10
試験片の厚さ	0.8	mm	-

電気的特性.	値	単位	テスト基準
ISO データ
耐トラッキング性	125	-	IEC 60112

その他の特性.	値	単位	テスト基準
密度	1630	kg/m³	ISO 1183

機能

特殊な特性

成形加工法.

射出成形.

納入形状.

顆粒., ナチュラルカラー

添加剤.

離型剤.

特殊な特性.

難燃., 熱安定化.

耐薬品性

General Chemical Resistance

領域別の利用可能性

北アメリカ., ヨーロッパ., アジア/太平洋地域., 南・中央アメリカ., 近東/アフリカ

その他の情報

村遜速揃

The material is delivered in moisture-proof packaging ready for processing. Maximum recommended water content for best processing is 0.05%. Typical conditions with a desiccant drier: temperature 115° C, dew point -20°C or below, time 3-4h or more. Avoid excessive shear rates and high thermal stresses for better processing. Special care must be taken to avoid moisture absorption and contamination with other polymers when adding regrind material. Colour variation and mechanical properties reduction may occur and should always be carefully monitored.

Injection Molding Processing Parameters

Melt Temperature	Mold Temperature	Injection Speed
300 - 340°C	140 - 160°C	low-medium

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.