Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Pebax® MH 2030 - TPA - ARKEMA

Material Data Center offers the following functions for Pebax® MH 2030:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Pebax datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
商品の説明文
Polyether block amide Pebax® MH 2030 resin is a thermoplastic elastomer made of flexible polyether and rigid polyamide.
Pebax® MH 2030 resin is an inherently dissipative polymer and can be dry blended or compounded with an isolative polymer to lower the surface resistivity of the final part.

Refractive index according to an internal method is 1.508.


Main applications:
  • Permanent antistactic additive


Packaging:

This grade is delivered dried in sealed packaging (25 kg bags) ready to be processed.

Shelf Life:
Two years from the delivery. For any use above this limit, please refer to our technical services.
機械的特性乾燥/調湿単位テスト基準
ISO データ
引張弾性率 - / 80 MPa ISO 527
ショア硬さD 40 / * - ISO 7619-1
熱的特性乾燥/調湿単位テスト基準
ISO データ
溶融温度, 10°C/min 200 / * °C ISO 11357-1/-3
電気的特性.乾燥/調湿単位テスト基準
ISO データ
体積抵抗率 - / 100000 Ohm*m IEC 62631-3-1
表面抵抗率 * / 1E7 Ohm IEC 62631-3-2
その他の特性.乾燥/調湿単位テスト基準
吸水率 120 / * % Sim. to ISO 62
吸湿率 4.5 / * % Sim. to ISO 62
密度 1140 / 1140 kg/m³ ISO 1183
特殊な特性
成形加工法.
射出成形., その他の押出成形.
納入形状.
ペレット.
特殊な特性.
導電., 帯電防止.
領域別の利用可能性
その他の情報
村遜速揃

Processing conditions:

- Typical melt temperature (Min / Recommended / Max): 230°C / 240°C / 260°C.
- Typical mold temperature: 25–60°C.
- Drying time and temperature (only necessary for bags opened for more than two hours): 5-7 hours at 70-90°C.
その他の押出成形.

Processing conditions:

- Typical melt temperature (Min / Recommended / Max): 230°C / 250°C / 280°C
- Drying time and temperature (only necessary for bags opened for more than two hours): 5-7 hours at 70-90°C
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.