Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NORYL™ Resin SE1GFN2 - Europe - (PPE+PS)-GF20 - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for NORYL™ Resin SE1GFN2 - Europe:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Noryl datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - 機械的特性 - 熱的特性 - 電気的特性. - その他の特性. - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
商品の説明文
NORYL™ SE1GFN2 resin is a 20% glass reinforced blend of polyphenylene ether (PPE) + high impact polystyrene (HIPS). This injection moldable grade contains non-brominated, non-chlorinated flame retardant and carries a UL94 flame rating of 5VA at 2mm and V1 at 1.5mm along with UL746C Outdoor Suitability rating of F1 and RTI of 110C. NORYL SE1GFN2 exhibits high heat resistance, good dielectric strength, dimensional stability, hydrolytic stability, and very low moisture absorption. This material is an excellent candidate for a variety of applications such as solar frames, unattended power supply (UPS) inverter/charger, indoor and outdoor electrical enclosures / housings / connectors, and wall plates / sockets / switches.

UL Yellow Card Link E45329-236777
Processing/Physical Characteristics値単位テスト基準
ISO データ
メルトボリュームレイト, MVR 12 cm³/10min ISO 1133
温度 280 °C -
荷重 10 kg -
機械的特性値単位テスト基準
ISO データ
引張弾性率 5500 MPa ISO 527
破壊応力 80 MPa ISO 527
破壊ひずみ 2 % ISO 527
曲げ弾性率 4500 MPa ISO 178
シャルピー衝撃強さ, +23°C 30 kJ/m² ISO 179/1eU
シャルピー衝撃強さ, -30ﾟC 30 kJ/m² ISO 179/1eU
Izod impact strength, +23°C, 4mm 25 kJ/m² ISO 180/1U
Izod impact strength, -30°C, 4mm 25 kJ/m² ISO 180/1U
Ball indentation hardness 125 MPa ISO 2039-1
熱的特性値単位テスト基準
ISO データ
ビカット軟化温度, A 150 °C ISO 306
ビカット軟化温度, B 140 °C ISO 306
ビカット軟化温度, 120°C/h 50N 145 °C ISO 306
1.5mm厚さでの燃焼性 V-1 class IEC 60695-11-10
試験片の厚さ 1.5 mm -
厚さhでの燃焼性 V-0 class IEC 60695-11-10
試験片の厚さ 6.0 mm -
厚さhでの燃焼性 5V 5VA class IEC 60695-11-20
試験片の厚さ 2.0 mm -
熱伝導率 0.28 W/(m K) DIN 52616
グローワイヤ燃焼性指数 (GWFI) 960 °C IEC 60695-2-12
グローワイヤ燃焼性指数 (GWFI) 960 °C IEC 60695-2-12
グローワイヤ着火温度 (GWIT) 800 °C IEC 60695-2-13
GWIT - 試験片の厚さ 1 mm -
グローワイヤ着火温度 (GWIT) 800 °C IEC 60695-2-13
GWIT - 試験片の厚さ 2 mm -
電気的特性.値単位テスト基準
ISO データ
比誘電率, 1MHz 2.9 - IEC 62631-2-1
誘電正接, 1MHz 20 E-4 IEC 62631-2-1
体積抵抗率 1E13 Ohm*m IEC 62631-3-1
表面抵抗率 >1E15 Ohm IEC 62631-3-2
耐電圧 30 kV/mm IEC 60243-1
耐トラッキング性 225 - IEC 60112
その他の特性.値単位テスト基準
吸水率. 0.22 % Sim. to ISO 62
吸湿率 0.07 % Sim. to ISO 62
密度. 1250 kg/m³ ISO 1183
密度 1250 kg/m³ ASTM D 792
Processing Recommendation Injection Molding値単位テスト基準
Pre-drying - Temperature 100 - 120 °C -
Pre-drying - Time 2 - 3 h -
樹脂温度 280 - 300 °C -
金型温度 80 - 120 °C -
Feed temperature 60 - 80 °C -
Zone 1 240 - 260 °C -
Zone 2 260 - 280 °C -
Zone 3 280 - 300 °C -
特殊な特性
成形加工法.
射出成形.
添加剤.
難燃剤.
特殊な特性.
難燃.
耐薬品性
Hydrolytically Stable
アプリケーション
自動車
領域別の利用可能性
ヨーロッパ.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.