Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ALCOM PA6 900/1 GF30 TF15 SI2 IM - (PA6+PTFE)-GF30 - MOCOM Compounds GmbH & Co. KG

Material Data Center offers the following functions for ALCOM PA6 900/1 GF30 TF15 SI2 IM:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Alcom datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
機械的特性 - 熱的特性 - その他の特性.
Any use of this information falls under the rules of our disclaimer.
商品の説明文
Base PolymerPolyamide 6
Filler/Additive System30 % glass fibres,17 % PTFE/Silicone
Special Featureshigh stiffness,heat stabilised,improved sliding / wear
Market SegmentAutomotive,Machinery
Typical Applicationsfunctional components
機械的特性乾燥/調湿単位テスト基準
ISO データ
引張弾性率 7700 / - MPa ISO 527
破壊応力 95 / - MPa ISO 527
破壊ひずみ 3.9 / - % ISO 527
シャルピー衝撃強さ, +23°C 55 / - kJ/m² ISO 179/1eU
ノッチ付きシャルピー衝撃強さ, +23°C 20 / - kJ/m² ISO 179/1eA
熱的特性乾燥/調湿単位テスト基準
ISO データ
荷重たわみ温度, 1.80 MPa 203 / * °C ISO 75-1/-2
その他の特性.乾燥/調湿単位テスト基準
密度 1420 / - kg/m³ ISO 1183
特殊な特性
成形加工法.
射出成形.
領域別の利用可能性
北アメリカ., ヨーロッパ., アジア/太平洋地域., 近東/アフリカ
その他の情報
村遜速揃
Pre-Drying Conditions80 °C in a dry air (dessiccant) dryer
for 2-12 h
dependant on moisture content
Processing Injection Mouldingmelt temperature 270-290 °C
mould temperature 80-100 °C
Storagedry, protected from light
not above 30°C
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.