Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of THERMOLAST® M TM7MED - TPE - KRAIBURG TPE GmbH & Co. KG
unit conversion, PDF datasheet print, comparison with other plastics
Check here, which other Thermolast datasheets, application examples or technical articles are available in Material Data Center
• Medical application
Application Examples:
• Seals
• Mouthpieces
• Valves
• Soft touch
• Flexible connections
• Medical tubes
Material Advantage:
• Applicaton up to indirect blood contact
• Tested acord. USP Class IV and ISO 10993-5
• Tested according to ISO 10993-11, ISO 10993- 10, USP 6.6.1
• Adhesion to PP und HDPE
• Adapted for injection moulding and extrusion
• Very good compression set
• sterilizable (autoclave 134°C, gammaradiation 2x35 kGy, EtO)
Proprietà Meccaniche | Valore | Unitá | Norma del test | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO Data | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistenza a trazione | 13 | MPa | ISO 37 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Deformazione a rottura | 800 | % | ISO 37 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Deformazione residua dopo compressione a 70°C, 24h | 38 | % | ISO 815 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Deformazione residua dopo compressione a 100°C, 24h | 55 | % | ISO 815 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistenza alla lacerazione | 23.5 | kN/m | ISO 34-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Durezza Shore A | 68 | - | ISO 7619-1 |
Altre Proprietà | Valore | Unitá | Norma del test |
Massa volumica | 890 | kg/m³ | ISO 1183 |
Raccomandazione de Processabilità Stampaggio ad Iniezione | Valore | Unitá | Norma del test |
Pre-essiccamento - Temperatura | 60 - 80 | °C | - |
Pre-essiccamento - Tempo | 2 - 4 | h | - |
Temperatura di fusione | 200 - 250 | °C | - |
Temperatura dello stampo | 25 - 40 | °C | - |
Zona 1 | 180 - 200 | °C | - |
Zona 2 | 200 - 220 | °C | - |
Zona 3 | 220 - 250 | °C | - |
Pressione di Iniezione | 20 - 100 | MPa | - |
Contropressione | 2 - 10 | MPa | - |
Pressione di chiusura | 8 - 60 | MPa | - |
Tempo di residenza, massimo | 10 | min | - |
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.