Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Reny 1022HS - PAMXD6-GF50 - Mitsubishi Engineering-Plastics Corporation

Material Data Center offers the following functions for Reny 1022HS:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Reny datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caratteristiche Fisichesecco/condUnitáNorma del test
ISO Data
Indice di fusione di volume, MVR 3.31 / * cm³/10min ISO 1133
Temperatura 275 / * °C -
Carico 2.16 / * kg -
Indice di Fluiditá, MFI 5.5 g/10min ISO 1133
Temperatura 275 °C -
Carico 2.16 kg -
Ritiro di stampaggio, parallelo 0.3 / * % ISO 294-4, 2577
Ritiro di stampaggio, perpendicolare 0.6 / * % ISO 294-4, 2577
Proprietà Meccanichesecco/condUnitáNorma del test
ISO Data
Modulo a trazione 21900 / 21000 MPa ISO 527
Carico unitario a rottura 236 / 233 MPa ISO 527
Deformazione a rottura 1.5 / 1.6 % ISO 527
Modulo a flessione, 23°C 19100 / 19000 MPa ISO 178
Resistenza alla flessione 384 / 326 MPa ISO 178
Resistenza all'urto Charpy, +23°C 61 / 40 kJ/m² ISO 179/1eU
Resist. urto Charpy con intaglio, +23°C 12 / 12 kJ/m² ISO 179/1eA
Proprietà Termichesecco/condUnitáNorma del test
ISO Data
Temp.di inflessione sotto carico, 1.80 MPa 245 / * °C ISO 75-1/-2
Coeff.di dilatazione termica lin., parallelo 12 / * E-6/K ISO 11359-1/-2
Coeff.di dilatazione termica lin. , perpend. 43 / * E-6/K ISO 11359-1/-2
Reaz. al fuoco spess.nom. 1.5mm HB / * class IEC 60695-11-10
Spessore provato 1.6 / * mm -
Yellow Card disponibile sì / * - -
Proprietà Elettrichesecco/condUnitáNorma del test
ISO Data
Costante dielettrica relativa, 1MHz 4.65 / - - IEC 62631-2-1
Fattore di dissipazione, 1MHz 91 / - E-4 IEC 62631-2-1
Resistività volumica 1.1E14 / - Ohm*m IEC 62631-3-1
Rigidità dielettrica 33 / - kV/mm IEC 60243-1
Altre Proprietàsecco/condUnitáNorma del test
Assorbimento d'umidità 0.87 / * % Sim. alla ISO 62
Massa volumica 1660 / - kg/m³ ISO 1183
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 120 °C -
Pre-essiccamento - Tempo 3 h -
Temperatura dello stampo 120 - 140 °C -
Zona 1 270 °C -
Zona 2 275 °C -
Zona 3 280 °C -
Temperatura dell ugello 280 °C -
Velocità di Rotazione della Vite 60 - 150 rpm -
Pressione di Iniezione 20 - 150 MPa -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Applicazioni
Automotive, Elettrotecnica ed electrici, Polivalente
Disponibilità geografica
Nord America, Europa, Asia Oceano Pacifico, South and Central America, Near East/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.