Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of NOPLA® KE901 - PEN - Kolon Industries

Material Data Center offers the following functions for NOPLA® KE901:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Nopla datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Caratteristiche FisicheValoreUnitáNorma del test
ISO Data
Indice di Fluiditá, MFI 12 g/10min ISO 1133
Temperatura 275 °C -
Carico 2.16 kg -
Ritiro di stampaggio, parallelo 0.6 % ISO 294-4, 2577
Proprietà MeccanicheValoreUnitáNorma del test
ISO Data
Resistenza a trazione 64 MPa ISO 527
Modulo a flessione, 23°C 2900 MPa ISO 178
Resist. urto Charpy con intaglio, +23°C 3 kJ/m² ISO 179/1eA
ASTM Data
Resistenza alla trazione 63 MPa ASTM D 638
Modulo a flessione 2892 MPa ASTM D 790
Proprietà TermicheValoreUnitáNorma del test
ISO Data
Temperatura di fusione, 10°C/min 265 °C ISO 11357-1/-3
Temp.di inflessione sotto carico, 0.45 MPa 115 °C ISO 75-1/-2
Reazione al fuoco a spessore h V-2 class IEC 60695-11-10
Spessore provato 0.8 mm -
ASTM Data
UL 94 combustibilitá V-2 - UL 94
Spessore testati 0.8 mm -
DTUL a 66 psi 100 °C ASTM D 648
Temperatura di fusione 280 °C ASTM D 3418
Proprietà OtticheValoreUnitáNorma del test
ASTM Data
Opacità 2 % ASTM D 1003
Trasmissione luminosa 85 % ASTM D 1003
Altre ProprietàValoreUnitáNorma del test
Massa volumica 1340 kg/m³ ISO 1183
Densità 1340 kg/m³ ASTM D 792
Raccomandazione de Processabilità Stampaggio ad IniezioneValoreUnitáNorma del test
Pre-essiccamento - Temperatura 140 - 160 °C -
Pre-essiccamento - Tempo 3 - 6 h -
Umidità del Processo ≤0.08 % -
Temperatura dello stampo 30 - 80 °C -
Zona 1 200 - 240 °C -
Zona 2 250 - 270 °C -
Zona 3 250 - 280 °C -
Temperatura dell ugello 260 - 290 °C -
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Caratteristiche speciali
Trasparente
Caratteristiche
Omopolimero
Disponibilità geografica
Nord America, Asia Oceano Pacifico
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.