Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.
This is the free Material Data Center Datasheet of Desmopan 3385A - TPU - Covestro Deutschland AG
unit conversion, PDF datasheet print, comparison with other plastics, parameters for material models, CAE Interfaces
Check here, which other Desmopan datasheets, application examples or technical articles are available in Material Data Center
- Extrusion- and injection molding grade
- good wear resistance
- short cycle times
- high melt stability
Application: - hard - soft systems
- Hoses, non-reinforced
- Profiles
- Injection molded engineering parts
Proprietà Meccaniche | Valore | Unitá | Norma del test | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
ISO Data | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Carico Unitario al 10% di allungamento | 1.7 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Carico Unitario al 100% di allungamento | 5.6 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Carico Unitario al 300% di allungamento | 14 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Carico Unitario a rottura TPE | 53 | MPa | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Allungamento a rottura TPE | >300 | % | ISO 527 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Deformazione residua dopo compressione a 70°C, 24h | 42 | % | ISO 815 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistenza alla lacerazione | 70 | kN/m | ISO 34-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Resistenza all'abrasione | 30 | mm³ | ISO 4649 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Durezza Shore A | 85 | - | ISO 7619-1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Durezza Shore D | 33 | - | ISO 7619-1 |
Altre Proprietà | Valore | Unitá | Norma del test |
Massa volumica | 1200 | kg/m³ | ISO 1183 |
Max. water content: 0.05 %
Max. drying temperature: 80 °C
Drying time:
Dry air dryer 1-2 h
PROCESSING
Melt temperature: 190-210 °C
Mold temperature: 20-40 °C
Preprocessing
Max. Water content | ≤0.05 % |
Drying temperature | 70-110 °C |
Dry air dryer | 1-2 h |
Processing
Melt temperature | 175-205 °C |
Preprocessing
Max. Water content | ≤0.05 % |
Drying temperature | 70-110 °C |
Dry air dryer | 1-2 h |
Processing
Melt temperature | 175-205 °C |
Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.
Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.