Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of VESTAMID® L2141 BK 9.7504 - PA12 - Evonik Operations GmbH

Check here, which other Vestamid datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - Mechanical properties - Thermal properties - Electrical properties - Other properties - Diagrams

Any use of this information falls under the rules of our disclaimer.

Product Texts

High viscosity PA12-Plastic resin for the extrusion

VESTAMID® L2141 BK 9.7504 is a heatstabilized polyamide 12 compound for the extrusion of tubing (e.g. fuel lines) and semi-finished products. Tubing according to DIN 73 378, Type: PA 12-HL.

Properties of compounds based on PA12 vary little with changing humidity due to low moisture absorption. Parts made of this semi-crystalline material are characterized by exceptional impact strength, low coefficient of friction and good chemical resistance.

Pigmentation may affect values.

Inside the original and undamaged packaging, the product has a shelf life of at least 2 years when stored in dry rooms at temperatures not exceeding 30°C.

For information about processing of VESTAMID®, please follow the general commendations about “Processing of VESTAMID® compounds”. 
 
FOR FURTHER INFORMATION PLEASE CONTACT US AT EVONIK-HP@EVONIK.COM
OR VISIT OUR PRODUCT AT  WWW.VESTAMID.COM

Processing/Physical Characteristics	dry / cond	Unit	Test Standard
ISO Data
Melt volume-flow rate, MVR	25 / *	cm³/10min	ISO 1133
Temperature	275 / *	°C	-
Load	5 / *	kg	-
Molding shrinkage, parallel	0.7 / *	%	ISO 294-4, 2577
Molding shrinkage, normal	1.3 / *	%	ISO 294-4, 2577

Mechanical properties	dry / cond	Unit	Test Standard
ISO Data
Tensile Modulus	1550 / 1300	MPa	ISO 527
Yield stress	46 / 42	MPa	ISO 527
Yield strain	4 / 12	%	ISO 527
Nominal strain at break	>50 / >50	%	ISO 527
Charpy impact strength, +23°C	N / N	kJ/m²	ISO 179/1eU
Charpy impact strength, -30°C	N / N	kJ/m²	ISO 179/1eU
Charpy notched impact strength, +23°C	10 / 12	kJ/m²	ISO 179/1eA
Type of failure	C / C	-	-
Charpy notched impact strength, -30°C	8 / 8	kJ/m²	ISO 179/1eA
Type of failure	C / C	-	-

Thermal properties	dry / cond	Unit	Test Standard
ISO Data
Melting temperature, 10°C/min	178 / *	°C	ISO 11357-1/-3
Temp. of deflection under load, 1.80 MPa	50 / *	°C	ISO 75-1/-2
Temp. of deflection under load, 0.45 MPa	110 / *	°C	ISO 75-1/-2
Vicat softening temperature, B	140 / *	°C	ISO 306
Coeff. of linear therm. expansion, parallel	150 / *	E-6/K	ISO 11359-1/-2
Burning Behav. at 1.5 mm nom. thickn.	HB / *	class	IEC 60695-11-10
Thickness tested	1.6 / *	mm	-

Electrical properties	dry / cond	Unit	Test Standard
ISO Data
Relative permittivity, 100Hz	9.7 / 5	-	IEC 62631-2-1
Relative permittivity, 1MHz	4 / 3.5	-	IEC 62631-2-1
Dissipation factor, 100Hz	2100 / 1000	E-4	IEC 62631-2-1
Dissipation factor, 1MHz	1100 / 500	E-4	IEC 62631-2-1
Volume resistivity	1E10 / 5E10	Ohm*m	IEC 62631-3-1
Surface resistivity	* / 6E14	Ohm	IEC 62631-3-2
Electric strength	39 / 35	kV/mm	IEC 60243-1
Comparative tracking index	600 / 600	-	IEC 60112

Other properties	dry / cond	Unit	Test Standard
Water absorption	1.5 / *	%	Sim. to ISO 62
Humidity absorption	0.7 / *	%	Sim. to ISO 62
Density	1010 / 1020	kg/m³	ISO 1183

Diagrams

Characteristics

Processing

Injection Molding, Pipe/Tube Extrusion, Profile Extrusion, Other Extrusion

Delivery form

Pellets, Black

Additives

Lubricants

Special Characteristics

High impact or impact modified, Heat stabilized or stable to heat

Features

Tribologic Grade

Chemical Resistance

General Chemical Resistance

Regional Availability

North America, Europe, Asia Pacific, South and Central America, Near East/Africa

Chemical Media Resistance

Acids
	Acetic Acid (5% by mass) (23°C)
	Citric Acid solution (10% by mass) (23°C)
Bases
	Sodium Hydroxide solution (35% by mass) (23°C)
	Sodium Hydroxide solution (1% by mass) (23°C)
	Ammonium Hydroxide solution (10% by mass) (23°C)
Alcohols
	Isopropyl alcohol (23°C)
	Methanol (23°C)
	Ethanol (23°C)
Hydrocarbons
	n-Hexane (23°C)
	Toluene (23°C)
	iso-Octane (23°C)
Ketones
	Acetone (23°C)
Ethers
	Diethyl ether (23°C)
Mineral oils
	SAE 10W40 multigrade motor oil (23°C)
	Insulating Oil (23°C)
Standard Fuels
	ISO 1817 Liquid 1 (60°C)
	ISO 1817 Liquid 2 (60°C)
	ISO 1817 Liquid 3 (60°C)
	ISO 1817 Liquid 4 (60°C)
	Standard fuel without alcohol (pref. ISO 1817 Liquid C) (23°C)
	Standard fuel with alcohol (pref. ISO 1817 Liquid 4) (23°C)
	Diesel fuel (pref. ISO 1817 Liquid F) (23°C)
	Diesel fuel (pref. ISO 1817 Liquid F) (90°C)
	Diesel EN 590 (100°C)
Salt solutions
	Sodium Chloride solution (10% by mass) (23°C)
	Sodium Carbonate solution (20% by mass) (23°C)
	Sodium Carbonate solution (2% by mass) (23°C)
	Zinc Chloride solution (50% by mass) (23°C)
Other
	Ethyl Acetate (23°C)
	Hydrogen peroxide (23°C)
	DOT No. 4 Brake fluid (120°C)
	Water (23°C)

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.