Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ULTEM™ Resin CRS5011R - Americas - PEI - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for ULTEM™ Resin CRS5011R - Americas:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Ultem datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - Mechanical properties - Thermal properties - Electrical properties - Other properties - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Product Texts
Enhanced flow Polyetherimide copolymer (Tg 225C) with internal mold release and enhanced chemical resistance to strong acids, bases, aromatics and ketones. ECO Conforming.
Processing/Physical CharacteristicsValueUnitTest Standard
ISO Data
Melt volume-flow rate, MVR 20 cm³/10min ISO 1133
Temperature 360 °C -
Load 5 kg -
ASTM Data
Melt Flow Index, MFI 11 g/10min ASTM D 1238
Temperature 337 °C -
Load 6.6 kg -
Mechanical propertiesValueUnitTest Standard
ISO Data
Tensile Modulus 2900 MPa ISO 527
Yield stress 100 MPa ISO 527
Yield strain 8 % ISO 527
Stress at break 85 MPa ISO 527
Strain at break 50 % ISO 527
Flexural modulus 2900 MPa ISO 178
Charpy impact strength, +23°C N kJ/m² ISO 179/1eU
Charpy impact strength, -30°C N kJ/m² ISO 179/1eU
Charpy notched impact strength, +23°C 7 kJ/m² ISO 179/1eA
Charpy notched impact strength, -30°C 7 kJ/m² ISO 179/1eA
Izod impact strength, +23°C, 4mm N kJ/m² ISO 180/1U
Izod impact strength, -30°C, 4mm N kJ/m² ISO 180/1U
Izod notched impact strength, +23°C, 4mm 5 kJ/m² ISO 180/1A
Izod notched impact strength, -30°C, 4mm 5 kJ/m² ISO 180/1A
ASTM Data
Tensile Modulus 2900 MPa ASTM D 638
Tensile Strength at Yield 100 MPa ASTM D 638
Tensile Strength at Break 75 MPa ASTM D 638
Elongation at Yield 8 % ASTM D 638
Elongation at Break 60 % ASTM D 638
Flexural Modulus 3100 MPa ASTM D 790
Izod Impact notched, 1/8 in 59 J/m ASTM D 256
Izod Impact unnotched, 1/8 in 2100 J/m ASTM D 256
Thermal propertiesValueUnitTest Standard
ISO Data
Temp. of deflection under load, 1.80 MPa 198 °C ISO 75-1/-2
Temp. of deflection under load, 0.45 MPa 208 °C ISO 75-1/-2
Vicat softening temperature, A 220 °C ISO 306
Vicat softening temperature, B 215 °C ISO 306
Vicat softening temperature, 120°C/h 50N 215 °C ISO 306
ASTM Data
DTUL @ 66 psi 213 °C ASTM D 648
DTUL @ 264 psi 201 °C ASTM D 648
Vicat Temperature 227 °C ASTM D 1525
Thermal Conductivity, solid state 0.0447 W/(m K) ASTM C 177
Electrical propertiesValueUnitTest Standard
ISO Data
Volume resistivity >1E13 Ohm*m IEC 62631-3-1
Surface resistivity >1E15 Ohm IEC 62631-3-2
Comparative tracking index 150 - IEC 60112
ASTM Data
Dielectric Strength, Short Time 18 kV/mm ASTM D 149
Dissipation Factor, 60 Hz 0.0021 - ASTM D 150
Dielectric Constant, 60 Hz 3.2 - ASTM D 150
Other propertiesValueUnitTest Standard
Water absorption 1.2 % Sim. to ISO 62
Humidity absorption 0.2 % Sim. to ISO 62
Density 1280 kg/m³ ISO 1183
Density 1280 kg/m³ ASTM D 792
Processing Recommendation Injection MoldingValueUnitTest Standard
Pre-drying - Temperature 150 °C -
Pre-drying - Time 4 - 6 h -
Processing humidity ≤0.02 % -
Melt temperature 365 - 390 °C -
Mold temperature 135 - 165 °C -
Zone 1 345 - 365 °C -
Zone 2 355 - 375 °C -
Zone 3 365 - 390 °C -
Screw speed 40 - 70 rpm -
Back pressure 0.3 - 0.7 MPa -
Characteristics
Processing
Injection Molding
Chemical Resistance
General Chemical Resistance
Applications
Automotive
Regional Availability
North America
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.