Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ULTEM™ Resin AUT210 - Americas - PI - Saudi Basic Industries Corporation (SABIC)

Check here, which other Ultem datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - Mechanical properties - Thermal properties - Other properties - Processing Recommendation Injection Molding - Diagrams

Any use of this information falls under the rules of our disclaimer.

Product Texts

Transparent, Thermoplastic Polyimide (TPI). Glass transition Temperature (Tg) of 227degC. Haze onset temperature of 212degC (SABIC IP method). Very low outgassing and plateout, for automotive lighting applications where highly metallized, reflective surfaces are required.

Processing/Physical Characteristics	Value	Unit	Test Standard
ISO Data
Melt volume-flow rate, MVR	16	cm³/10min	ISO 1133
Temperature	360	°C	-
Load	5	kg	-
Density of melt	1120	kg/m³	-
Thermal conductivity of melt	0.16	W/(m K)	-
Spec. heat capacity of melt	2330	J/(kg K)	-
Ejection temperature	207	°C	-
ASTM Data
Melt Flow Index, MFI	11	g/10min	ASTM D 1238
Temperature	337	°C	-
Load	6.6	kg	-

Mechanical properties	Value	Unit	Test Standard
ISO Data
Tensile Modulus	3320	MPa	ISO 527
Yield stress	103	MPa	ISO 527
Yield strain	7	%	ISO 527
Stress at break	88	MPa	ISO 527
Strain at break	50	%	ISO 527
Flexural modulus	3140	MPa	ISO 178
Charpy notched impact strength, +23°C	16	kJ/m²	ISO 179/1eA
Izod impact strength, +23°C, 4mm	N	kJ/m²	ISO 180/1U
Izod impact strength, -30°C, 4mm	N	kJ/m²	ISO 180/1U
Izod notched impact strength, +23°C, 4mm	5	kJ/m²	ISO 180/1A
Izod notched impact strength, -30°C, 4mm	4	kJ/m²	ISO 180/1A
ASTM Data
Tensile Modulus	3590	MPa	ASTM D 638
Tensile Strength at Yield	105	MPa	ASTM D 638
Tensile Strength at Break	88	MPa	ASTM D 638
Elongation at Yield	8	%	ASTM D 638
Elongation at Break	75	%	ASTM D 638
Flexural Modulus	3330	MPa	ASTM D 790
Izod Impact notched, 1/8 in	37	J/m	ASTM D 256
Izod Impact notched, Low-Temperature	38	J/m	ASTM D 256
Temperature	-30	°C	-
Izod Impact unnotched, 1/8 in	2440	J/m	ASTM D 256

Thermal properties	Value	Unit	Test Standard
ISO Data
Vicat softening temperature, B	221	°C	ISO 306
Coeff. of linear therm. expansion, parallel	41.4	E-6/K	ISO 11359-1/-2
Coeff. of linear therm. expansion, normal	41	E-6/K	ISO 11359-1/-2
ASTM Data
DTUL @ 66 psi	215	°C	ASTM D 648
DTUL @ 264 psi	201	°C	ASTM D 648
Vicat Temperature	222	°C	ASTM D 1525

Other properties	Value	Unit	Test Standard
Water absorption	1.03	%	Sim. to ISO 62
Humidity absorption	0.2	%	Sim. to ISO 62
Density	1290	kg/m³	ISO 1183
Density	1290	kg/m³	ASTM D 792

Processing Recommendation Injection Molding	Value	Unit	Test Standard
Pre-drying - Temperature	150	°C	-
Pre-drying - Time	4 - 6	h	-
Processing humidity	≤0.02	%	-
Melt temperature	380 - 405	°C	-
Mold temperature	135 - 165	°C	-
Zone 1	360 - 380	°C	-
Zone 2	370 - 395	°C	-
Zone 3	380 - 405	°C	-
Screw speed	40 - 70	rpm	-
Back pressure	0.3 - 0.7	MPa	-

Diagrams

Characteristics

Processing

Injection Molding

Special Characteristics

Transparent

Applications

Automotive

Regional Availability

North America

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.