Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ULTEM™ Resin 4001 - Europe - (PEI+PTFE) - Saudi Basic Industries Corporation (SABIC)

Material Data Center offers the following functions for ULTEM™ Resin 4001 - Europe:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Ultem datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - Mechanical properties - Thermal properties - Electrical properties - Other properties - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Product Texts
PTFE filled, standard flow Polyetherimide (Tg 217C). ECO Conforming, UL94 V0 and 5VA listing.

UL Yellow Card Link E121562-221110
Processing/Physical CharacteristicsValueUnitTest Standard
ISO Data
Melt volume-flow rate, MVR 13 cm³/10min ISO 1133
Temperature 360 °C -
Load 5 kg -
Mechanical propertiesValueUnitTest Standard
ISO Data
Tensile Modulus 3000 MPa ISO 527
Yield stress 95 MPa ISO 527
Yield strain 6 % ISO 527
Stress at break 75 MPa ISO 527
Strain at break 30 % ISO 527
Flexural modulus 3000 MPa ISO 178
Charpy notched impact strength, +23°C 11 kJ/m² ISO 179/1eA
Charpy notched impact strength, -30°C 9 kJ/m² ISO 179/1eA
Izod notched impact strength, +23°C, 4mm 10 kJ/m² ISO 180/1A
Izod notched impact strength, -30°C, 4mm 8 kJ/m² ISO 180/1A
Ball indentation hardness 130 MPa ISO 2039-1
Thermal propertiesValueUnitTest Standard
ISO Data
Vicat softening temperature, A 215 °C ISO 306
Vicat softening temperature, B 208 °C ISO 306
Vicat softening temperature, 120°C/h 50N 210 °C ISO 306
Burning behav. at thickness h V-0 class IEC 60695-11-10
Thickness tested 0.4 mm -
Burning behav. 5V at thickness h 5VA class IEC 60695-11-20
Thickness tested 1.5 mm -
Thermal Conductivity 0.26 W/(m K) DIN 52616
Glow Wire Flammability Index (GWFI) 960 °C IEC 60695-2-12
GWFI - thickness tested (3) 3.2 mm -
Electrical propertiesValueUnitTest Standard
ISO Data
Volume resistivity 1E13 Ohm*m IEC 62631-3-1
Surface resistivity >1E15 Ohm IEC 62631-3-2
Comparative tracking index 150 - IEC 60112
Other propertiesValueUnitTest Standard
Water absorption 1.1 % Sim. to ISO 62
Humidity absorption 0.6 % Sim. to ISO 62
Density 1330 kg/m³ ISO 1183
Processing Recommendation Injection MoldingValueUnitTest Standard
Pre-drying - Temperature 150 °C -
Pre-drying - Time 4 - 6 h -
Processing humidity ≤0.02 % -
Melt temperature 370 - 410 °C -
Mold temperature 140 - 180 °C -
Feed temperature 80 - 120 °C -
Zone 1 340 - 395 °C -
Zone 2 350 - 405 °C -
Zone 3 360 - 415 °C -
Characteristics
Processing
Injection Molding
Regional Availability
Europe
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.