Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of POLYFORT® FPP 30 GFC K1079 - PP-GF30 - LyondellBasell Industries

Check here, which other Polyfort datasheets, application examples or technical articles are available in Material Data Center

Processing/Physical Characteristics - Mechanical properties - Thermal properties - Electrical properties - Other properties - Processing Recommendation Injection Molding - Diagrams

Any use of this information falls under the rules of our disclaimer.

Product Texts

30% chemical coupled glass fibre reinforced PP-homopolymer; long term heat stabilized; meets VW-TL PP10

Processing/Physical Characteristics	Value	Unit	Test Standard
ISO Data
Melt volume-flow rate, MVR	5	cm³/10min	ISO 1133
Temperature	230	°C	-
Load	2.16	kg	-
Molding shrinkage, parallel	0.2	%	ISO 294-4, 2577
Molding shrinkage, normal	1.2	%	ISO 294-4, 2577
Density of melt	970	kg/m³	-
Thermal conductivity of melt	0.155	W/(m K)	-
Spec. heat capacity of melt	2000	J/(kg K)	-

Mechanical properties	Value	Unit	Test Standard
ISO Data
Tensile Modulus	6700	MPa	ISO 527
Stress at break	85	MPa	ISO 527
Strain at break	3	%	ISO 527
Charpy impact strength, +23°C	48	kJ/m²	ISO 179/1eU
Charpy impact strength, -30°C	45	kJ/m²	ISO 179/1eU
Charpy notched impact strength, +23°C	9	kJ/m²	ISO 179/1eA
Charpy notched impact strength, -30°C	8	kJ/m²	ISO 179/1eA

Thermal properties	Value	Unit	Test Standard
ISO Data
Melting temperature, 10°C/min	168	°C	ISO 11357-1/-3
Temp. of deflection under load, 1.80 MPa	145	°C	ISO 75-1/-2
Temp. of deflection under load, 0.45 MPa	159	°C	ISO 75-1/-2
Vicat softening temperature, B	131	°C	ISO 306
Coeff. of linear therm. expansion, parallel	25	E-6/K	ISO 11359-1/-2
Coeff. of linear therm. expansion, normal	95	E-6/K	ISO 11359-1/-2
Coeff. of linear therm. expansion -40°C to +100°C, parallel	20	E-6/K	ISO 11359-1/-2
Coeff. of linear therm. expansion -40°C to +100°C, normal	115	E-6/K	ISO 11359-1/-2
Burning Behav. at 1.5 mm nom. thickn.	HB	class	IEC 60695-11-10
Thickness tested	1.5	mm	-
Yellow Card available	yes	-	-
Burning Behav. at thickness h	HB	class	IEC 60695-11-10
Thickness tested	3.0	mm	-
Yellow Card available	yes	-	-
Burning rate, FMVSS, Thickness 1 mm	50	mm/min	ISO 3795 (FMVSS 302)

Electrical properties	Value	Unit	Test Standard
ISO Data
Volume resistivity	>1E13	Ohm*m	IEC 62631-3-1
Surface resistivity	>1E15	Ohm	IEC 62631-3-2

Other properties	Value	Unit	Test Standard
Density	1130	kg/m³	ISO 1183

Processing Recommendation Injection Molding	Value	Unit	Test Standard
Pre-drying - Temperature	80	°C	-
Pre-drying - Time	2 - 4	h	-
Melt temperature	230 - 270	°C	-
Mold temperature	40 - 70	°C	-

Diagrams

Characteristics

Processing

Injection Molding

Delivery form

Granules

Additives

Release agent

Special Characteristics

U.V. stabilized or stable to weather, Heat stabilized or stable to heat

Regional Availability

North America, Europe, Asia Pacific, South and Central America, Near East/Africa

Other text information

Injection molding

PREPROCESSING; Pretreatment
Predrying usually not neccessary (2-4h / 80°C)

PROCESSING ;Processing:

Melttemperature	230 - 270	°C
Mouldtemperature	40 - 70	°C

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.