Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Luran® 378P - SAN - INEOS Styrolution

Material Data Center offers the following functions for Luran® 378P:
unit conversion, PDF datasheet print, comparison with other plastics, flow length calculation, snap fit calculation, beam deflection calculation, cooling time calculation, parameters for material models, CAE Interfaces

Check here, which other Luran datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Product Texts
Easy-flow grade with enhanced resistance to chemicals.
Processing/Physical CharacteristicsValueUnitTest Standard
ISO Data
Melt volume-flow rate, MVR 20 cm³/10min ISO 1133
Temperature 220 °C -
Load 10 kg -
Density of melt 970 kg/m³ -
Thermal conductivity of melt 0.17 W/(m K) -
Spec. heat capacity of melt 2300 J/(kg K) -
Ejection temperature 98 °C -
Mechanical propertiesValueUnitTest Standard
ISO Data
Tensile Modulus 3800 MPa ISO 527
Stress at break 75 MPa ISO 527
Strain at break 3.5 % ISO 527
Tensile creep modulus, 1h 3500 MPa ISO 899-1
Tensile creep modulus, 1000h 2800 MPa ISO 899-1
Charpy impact strength, +23°C 19 kJ/m² ISO 179/1eU
Charpy impact strength, -30°C 19 kJ/m² ISO 179/1eU
Charpy notched impact strength, +23°C 2 kJ/m² ISO 179/1eA
Thermal propertiesValueUnitTest Standard
ISO Data
Temp. of deflection under load, 1.80 MPa 89 °C ISO 75-1/-2
Temp. of deflection under load, 0.45 MPa 101 °C ISO 75-1/-2
Vicat softening temperature, B 107 °C ISO 306
Coeff. of linear therm. expansion, parallel 70 E-6/K ISO 11359-1/-2
Burning Behav. at 1.5 mm nom. thickn. HB class IEC 60695-11-10
Thickness tested 1.6 mm -
Yellow Card available yes - -
Oxygen index 18 % ISO 4589-1/-2
Electrical propertiesValueUnitTest Standard
ISO Data
Relative permittivity, 100Hz 3 - IEC 62631-2-1
Relative permittivity, 1MHz 2.7 - IEC 62631-2-1
Dissipation factor, 100Hz 50 E-4 IEC 62631-2-1
Dissipation factor, 1MHz 80 E-4 IEC 62631-2-1
Volume resistivity >1E13 Ohm*m IEC 62631-3-1
Surface resistivity >1E15 Ohm IEC 62631-3-2
Comparative tracking index 425 - IEC 60112
Other propertiesValueUnitTest Standard
Humidity absorption 0.3 % Sim. to ISO 62
Density 1080 kg/m³ ISO 1183
Test specimen productionValueUnitTest Standard
ISO Data
Injection Molding, melt temperature 230 °C ISO 294
Injection Molding, mold temperature 50 °C ISO 294
Injection Molding, injection velocity 200 mm/s ISO 294
Processing Recommendation Injection MoldingValueUnitTest Standard
Pre-drying - Temperature 80 °C -
Pre-drying - Time 2 - 4 h -
Melt temperature 220 - 260 °C -
Mold temperature 40 - 80 °C -
Diagrams
Viscosity-shear rate , Luran® 378P, SAN, INEOS Styrolution
Shearstress-shear rate , Luran® 378P, SAN, INEOS Styrolution
Dynamic Shear modulus-temperature , Luran® 378P, SAN, INEOS Styrolution
Stress-strain , Luran® 378P, SAN, INEOS Styrolution
Secant modulus-strain , Luran® 378P, SAN, INEOS Styrolution
Stress-strain (isochronous) 23°C, Luran® 378P, SAN, INEOS Styrolution
Creep modulus-time 23°C, Luran® 378P, SAN, INEOS Styrolution
Creep curve 23°C, Luran® 378P, SAN, INEOS Styrolution
Stress-strain (isochronous) 40°C, Luran® 378P, SAN, INEOS Styrolution
Creep modulus-time 40°C, Luran® 378P, SAN, INEOS Styrolution
Creep curve 40°C, Luran® 378P, SAN, INEOS Styrolution
Stress-strain (isochronous) 60°C, Luran® 378P, SAN, INEOS Styrolution
Creep modulus-time 60°C, Luran® 378P, SAN, INEOS Styrolution
Creep curve 60°C, Luran® 378P, SAN, INEOS Styrolution
Stress-strain (isochronous) 80°C, Luran® 378P, SAN, INEOS Styrolution
Creep modulus-time 80°C, Luran® 378P, SAN, INEOS Styrolution
Creep curve 80°C, Luran® 378P, SAN, INEOS Styrolution
Specific volume-temperature (pvT) , Luran® 378P, SAN, INEOS Styrolution
Tensile modulus-temperature , Luran® 378P, SAN, INEOS Styrolution
Characteristics
Processing
Injection Molding
Delivery form
Pellets
Special Characteristics
Transparent
Regional Availability
Other text information
Injection molding
PREPROCESSING
Pre/Post-processing, Pre-drying, Temperature: 80 °C
Pre/Post-processing, Pre-drying, Time: 2 - 4 h

PROCESSING
injection molding, Melt temperature, range: 220 - 260 °C
injection molding, Melt temperature, recommended: 250 °C
injection molding, Mold temperature, range: 40 - 80 °C
injection molding, Mold temperature, recommended: 50 °C
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.