Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of LUCEL FW700S - POM - LG Chem

Material Data Center offers the following functions for LUCEL FW700S:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Lucel datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - Mechanical properties - Thermal properties - Electrical properties - Other properties - Processing Recommendation Injection Molding
Any use of this information falls under the rules of our disclaimer.
Processing/Physical CharacteristicsValueUnitTest Standard
ASTM Data
Melt Flow Index, MFI 10 g/10min ASTM D 1238
Temperature 190 °C -
Load 2.16 kg -
Mold Shrinkage, MD 0.021 mm/mm ASTM D 955
Mechanical propertiesValueUnitTest Standard
ASTM Data
Tensile Strength at Yield 54 MPa ASTM D 638
Elongation at Break 70 % ASTM D 638
Flexural Modulus 2354 MPa ASTM D 790
Flexural Strength 78.5 MPa ASTM D 790
Rockwell Hardness R 80 - ASTM D 785
Izod Impact notched, 1/4 in 84.8 J/m ASTM D 256
Thermal propertiesValueUnitTest Standard
ASTM Data
UL 94 Flame rating HB - UL 94
Thickness tested 0.95 mm -
DTUL @ 66 psi 155 °C ASTM D 648
DTUL @ 264 psi 105 °C ASTM D 648
Electrical propertiesValueUnitTest Standard
ASTM Data
Surface Resistivity 1E14 Ohm ASTM D 257
Volume Resistivity 1E16 Ohm*cm ASTM D 257
Other propertiesValueUnitTest Standard
Density 1400 kg/m³ ASTM D 792
Processing Recommendation Injection MoldingValueUnitTest Standard
Pre-drying - Temperature 90 - 110 °C -
Pre-drying - Time 2 - 3 h -
Processing humidity ≤0.1 % -
Melt temperature 200 - 220 °C -
Mold temperature 80 - 110 °C -
Zone 1 160 - 180 °C -
Zone 2 170 - 190 °C -
Zone 3 180 - 200 °C -
Nozzle temperature 180 - 200 °C -
Screw speed 50 - 100 rpm -
Back pressure 0.5 - 3 MPa -
Characteristics
Processing
Injection Molding
Features
Anti Slip
Regional Availability
North America, Europe, Asia Pacific, South and Central America
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.