Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of LEMALLOY C82HL - (PPE+PA66) - Mitsubishi Engineering-Plastics Corporation

Material Data Center offers the following functions for LEMALLOY C82HL:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Lemalloy datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Processing/Physical Characteristicsdry / condUnitTest Standard
ISO Data
Melt volume-flow rate, MVR 90 / * cm³/10min ISO 1133
Temperature 280 / * °C -
Load 5 / * kg -
Molding shrinkage, parallel 1.2 / * % ISO 294-4, 2577
Molding shrinkage, normal 1.2 / * % ISO 294-4, 2577
Mechanical propertiesdry / condUnitTest Standard
ISO Data
Tensile Modulus 2600 / 1500 MPa ISO 527
Yield stress 60 / 45 MPa ISO 527
Yield strain 4.8 / 19 % ISO 527
Strain at break 47 / 88 % ISO 527
Flexural modulus, 23°C 2400 / 1500 MPa ISO 178
Flexural strength 90 / 60 MPa ISO 178
Charpy impact strength, +23°C N / N kJ/m² ISO 179/1eU
Charpy notched impact strength, +23°C 20 / 62 kJ/m² ISO 179/1eA
Thermal propertiesdry / condUnitTest Standard
ISO Data
Temp. of deflection under load, 1.80 MPa 70 / * °C ISO 75-1/-2
Temp. of deflection under load, 0.45 MPa 165 / * °C ISO 75-1/-2
Electrical propertiesdry / condUnitTest Standard
ISO Data
Relative permittivity, 1MHz 3.2 / - - IEC 62631-2-1
Dissipation factor, 1MHz 120 / - E-4 IEC 62631-2-1
Volume resistivity 2E13 / - Ohm*m IEC 62631-3-1
Surface resistivity * / 7E14 Ohm IEC 62631-3-2
Electric strength 33 / - kV/mm IEC 60243-1
Other propertiesdry / condUnitTest Standard
Density 1130 / - kg/m³ ISO 1183
Processing Recommendation Injection MoldingValueUnitTest Standard
Pre-drying - Temperature 110 - 120 °C -
Pre-drying - Time 2 - 4 h -
Mold temperature 60 - 100 °C -
Zone 1 240 - 260 °C -
Zone 2 250 - 280 °C -
Zone 3 250 - 280 °C -
Nozzle temperature 250 - 280 °C -
Screw speed 60 - 150 rpm -
Injection pressure 20 - 150 MPa -
Characteristics
Processing
Injection Molding
Features
Acoustical Barrier Properties
Applications
Automotive, Electrical and Electronical, General Purpose
Regional Availability
North America, Europe, Asia Pacific, South and Central America, Near East/Africa
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.