Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Kocetal® TC704 - POM-T20 - Kolon Industries

Material Data Center offers the following functions for Kocetal® TC704:
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Kocetal datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Processing/Physical CharacteristicsValueUnitTest Standard
ISO Data
Melt flow index, MFI 20 g/10min ISO 1133
Temperature 190 °C -
Load 2.16 kg -
Molding shrinkage, parallel 1.6 % ISO 294-4, 2577
ASTM Data
Melt Flow Index, MFI 20 g/10min ASTM D 1238
Temperature 190 °C -
Load 2.16 kg -
Mold Shrinkage, MD 0.016 mm/mm ASTM D 955
Mechanical propertiesValueUnitTest Standard
ISO Data
Tensile Strength 55 MPa ISO 527
Strain at break 5 % ISO 527
Flexural modulus, 23°C 4000 MPa ISO 178
Charpy notched impact strength, +23°C 5.2 kJ/m² ISO 179/1eA
Rockwell hardness M 85 - ISO 2039-2
ASTM Data
Tensile Strength 60 MPa ASTM D 638
Elongation at Break 7.5 % ASTM D 638
Flexural Modulus 5300 MPa ASTM D 790
Flexural Strength 105 MPa ASTM D 790
Rockwell Hardness M 84 - ASTM D 785
Izod Impact notched, 1/8 in 33 J/m ASTM D 256
Thermal propertiesValueUnitTest Standard
ISO Data
Melting temperature, 10°C/min 166 °C ISO 11357-1/-3
Temp. of deflection under load, 1.80 MPa 125 °C ISO 75-1/-2
ASTM Data
UL 94 Flame rating HB - UL 94
Thickness tested 0.8 mm -
Coefficient of Thermal Expansion, MD 60 E-6/K ASTM D 696
DTUL @ 66 psi 163 °C ASTM D 648
DTUL @ 264 psi 145 °C ASTM D 648
Melting Temperature 166 °C ASTM D 3418
Electrical propertiesValueUnitTest Standard
ISO Data
Volume resistivity 1E12 Ohm*m IEC 62631-3-1
Surface resistivity >1E15 Ohm IEC 62631-3-2
Electric strength 19 kV/mm IEC 60243-1
ASTM Data
Dielectric Strength, Short Time 19 kV/mm ASTM D 149
Dissipation Factor, 1 MHz 0.006 - ASTM D 150
Surface Resistivity >1E15 Ohm ASTM D 257
Volume Resistivity >1E15 Ohm*cm ASTM D 257
Other propertiesValueUnitTest Standard
Density 1560 kg/m³ ISO 1183
Water Absorption, 24hr 0.2 % ASTM D 570
Density 1560 kg/m³ ASTM D 792
Processing Recommendation Injection MoldingValueUnitTest Standard
Pre-drying - Temperature 80 - 90 °C -
Pre-drying - Time 3 h -
Melt temperature ≤220 °C -
Mold temperature 60 - 80 °C -
Zone 1 180 °C -
Zone 2 190 °C -
Zone 3 190 °C -
Nozzle temperature 200 °C -
Characteristics
Processing
Injection Molding
Regional Availability
North America, Asia Pacific
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.