Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of EMERGE™ PC 8702-15 (AP) - PC-GX20 - Trinseo

Material Data Center offers the following functions for EMERGE™ PC 8702-15 (AP):
unit conversion, PDF datasheet print, comparison with other plastics

Check here, which other Emerge datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Any use of this information falls under the rules of our disclaimer.
Processing/Physical CharacteristicsValueUnitTest Standard
ASTM Data
Melt Flow Index, MFI 15 g/10min ASTM D 1238
Temperature 300 °C -
Load 1.2 kg -
Mold Shrinkage, MD 0.003 mm/mm ASTM D 955
Mechanical propertiesValueUnitTest Standard
ASTM Data
Tensile Modulus 3999 MPa ASTM D 638
Tensile Strength at Break 100 MPa ASTM D 638
Elongation at Break 4 % ASTM D 638
Izod Impact notched, 1/8 in 112 J/m ASTM D 256
Thermal propertiesValueUnitTest Standard
ASTM Data
UL 94 Flame rating V-0 - UL 94
Thickness tested 1.5 mm -
DTUL @ 66 psi 145 °C ASTM D 648
DTUL @ 264 psi 140 °C ASTM D 648
Electrical propertiesValueUnitTest Standard
ISO Data
Comparative tracking index 175 - IEC 60112
ASTM Data
Dielectric Strength, Short Time 27.2 kV/mm ASTM D 149
Dielectric Constant, 1 MHz 3.1 - ASTM D 150
Surface Resistivity 3E14 Ohm ASTM D 257
Volume Resistivity >1E15 Ohm*cm ASTM D 257
Other propertiesValueUnitTest Standard
Density 1330 kg/m³ ASTM D 792
Processing Recommendation Injection MoldingValueUnitTest Standard
Pre-drying - Temperature 121 °C -
Pre-drying - Time 3 - 4 h -
Melt temperature 288 - 316 °C -
Mold temperature 79.4 - 116 °C -
Characteristics
Processing
Injection Molding
Additives
Release agent
Special Characteristics
Flame retardant, Phosphorus-free
Applications
IT / Business Machine, Electrical and Electronical
Regional Availability
Asia Pacific
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.