Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ALCOM PP 620/8 GF30 PTFE15 - (PP+PTFE)-GF30 - MOCOM Compounds GmbH & Co. KG

Material Data Center offers the following functions for ALCOM PP 620/8 GF30 PTFE15:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Alcom datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Processing/Physical Characteristics - Mechanical properties - Thermal properties - Other properties
Any use of this information falls under the rules of our disclaimer.
Product Texts
Base PolymerPolypropylene Homopolymer
Filler/Additive System30 % glass fibres,15 % PTFE
Special Featuresheat stabilised,improved sliding / wear
Market SegmentAutomotive,Machinery
Application Areavarious
Processing/Physical CharacteristicsValueUnitTest Standard
ISO Data
Melt volume-flow rate, MVR 4 cm³/10min ISO 1133
Temperature 230 °C -
Load 2.16 kg -
Mechanical propertiesValueUnitTest Standard
ISO Data
Tensile Modulus 6700 MPa ISO 527
Stress at break 82 MPa ISO 527
Strain at break 2.7 % ISO 527
Charpy impact strength, +23°C 44 kJ/m² ISO 179/1eU
Charpy notched impact strength, +23°C 9 kJ/m² ISO 179/1eA
Thermal propertiesValueUnitTest Standard
ISO Data
Temp. of deflection under load, 1.80 MPa 148 °C ISO 75-1/-2
Vicat softening temperature, B 136 °C ISO 306
Other propertiesValueUnitTest Standard
Density 1250 kg/m³ ISO 1183
Characteristics
Processing
Injection Molding
Regional Availability
North America, Europe, Asia Pacific, South and Central America, Near East/Africa
Other text information
Injection molding
Pre-Drying Conditionsin a dry air (dessiccant) dryer 80-100 °C
for 2-3 h
in an air circulating dryer 80-100 °C
for 2-4 h
dependant on moisture content
Processing Injection Mouldingmelt temperature 200-270 °C
mould temperature 29-90 °C
Storagedry, protected from light
not above 30°C
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.