Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of ALCOM PBT 700/1.1 CF20 PTFE15 - (PBT+PTFE)-CF20 - MOCOM Compounds GmbH & Co. KG

Material Data Center offers the following functions for ALCOM PBT 700/1.1 CF20 PTFE15:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Alcom datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Mechanical properties - Thermal properties - Electrical properties - Other properties
Any use of this information falls under the rules of our disclaimer.
Product Texts
Base PolymerPolybutylene Terephthalate
Filler/Additive System20 % carbon fibres,15 % PTFE
Special Featureselectrically conductive,reduced surface resistivity,improved sliding / wear,heat stabilised
Market SegmentMachinery
Application Areainjection moulded parts
Typical Applicationshousings,functional components
Mechanical propertiesValueUnitTest Standard
ISO Data
Tensile Modulus 16200 MPa ISO 527
Stress at break 140 MPa ISO 527
Strain at break 1.6 % ISO 527
Charpy impact strength, +23°C 37 kJ/m² ISO 179/1eU
Charpy notched impact strength, +23°C 6 kJ/m² ISO 179/1eA
Thermal propertiesValueUnitTest Standard
ISO Data
Temp. of deflection under load, 1.80 MPa 217 °C ISO 75-1/-2
Vicat softening temperature, B 210 °C ISO 306
Electrical propertiesValueUnitTest Standard
ISO Data
Surface resistivity 25 Ohm IEC 62631-3-2
Other propertiesValueUnitTest Standard
Density 1470 kg/m³ ISO 1183
Characteristics
Processing
Injection Molding
Special Characteristics
Increased electrical conductivity
Regional Availability
North America, Europe, Asia Pacific, South and Central America, Near East/Africa
Other text information
Injection molding
Pre-Drying Conditionsin a dry air (dessiccant) dryer 100-120 °C
for 2-4 h
in an air circulating dryer 100-120 °C
for 4-8 h
dependant on moisture content
Processing Injection Mouldingmelt temperature 250-270 °C
mould temperature 80-120 °C
Storagedry, protected from light
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.